COMPLETE DIY “Mobile Spray Rig”™ E-30 SPRAY PACKAGE
THE ORIGINAL“ULTIMATE PLUG & PLAY QUICK START”
DESIGN
THE ONLY PRE-ASSEMBLED UNIT ON THE MARKET
Fully equipped and ready to be bolted into your pre-owned truck or trailer,
Pneumatics include pre-plumbed distribution manifold, Feed lines are
pre-assembled and tested, this kit even includes mounting hardware and personal protection gear making this truly a
bolt in and ready to go assembly over a weekend.
TM300 Hose Rack (Patented Design used in Tons of our Rig Layouts over the last 10 Years) Req’s 6’ 8” Overhead
- Easily Accommodates 310’ Heated Hose without the Worry of Damage from Stress and Hose Overtemp
- Elevated Proportioner Area, Pump Holders and Air Manifold. Built to Accommodate Additional Accessories
- Minimizes Installation Time and Substantially Increasing your Rig Footprint
- Improves Rig Aesthetics, Promotes Good Housekeeping and Enhances Maintenance Procedures
Graco E30 Reactor Proportioner Wired Single Ø (78 Amp) or Three Ø (50
Amp) @ 240 V
- Flow Output up to 20lbs. Per Minute, the Most Popular Proportioner for Spray Foam Insulators
- Capable of 2,000 PSI and Accommodating up to 200’ of Heated Hose
Graco Air Purge Fusion Gun (Proven to be the Easiest Gun Used on the Market)
- Complete with the 01 Mix Chamber (Produces an 11” Round Pattern at 20-24” from Target)
- Weighs only 3.1lbs with Manifold, Easy to Operate and Low Maintenance
100’ of Graco Heated Hoses (Complete with Braided Mesh Scuffjacket)
- 2,750 lb. Rating with Thermocouple Controller that Creates Precision Chemical Heat Stabilization
10’ Graco Heated Whip (with Gun Manifold and Scuffjacket)
- Insures Chemical Temperature Stabilization to the Gun, Fatigue Reduction “ FLEX” Design
Chemical Return Recirculation Assembly with Desiccant Driers
- Provides Proper Drum Ventilation and Assures Moisture Free Operation and Chemical Stabilization
- Provides Quick Start-Ups unsurpassed by your Competitors and Aids in Crystallization Prevention
Drum Mounting Station
- Includes E-Track, E-Track Clips and Ratchet Straps for Safe and Proper Drum Transport
2:1 Fluid Transfer Pumps with Feed Hoses
- Durable Stainless Steel Construction, Flow Output (Intermittent) of over 3 GPM
PPE Starter Pack
- Solvent Flush Kit, Gun Cleaning Kit, Niosh Approved Isocyanate Half Mask Cartridge Respirator, Safety Goggles & Safety Glasses, Non-Sparking 55 Gallon Drum Bung Wrench, 36” Shaver Blade for ½ lb. Foams, Disposable Coveralls, Rubber and Cotton Gloves
AVAILABLE WITHIN 5 DAYS OR LESS OF ORDER, CALL FOR PRICING
OPTIMIZE YOUR PURCHASE WITH OUR “HIGHLY
RECOMMENDED” OPTIONS:
____Refrigerant Air Dryer: Ensures Clean Dry Air to Gun (Cord & Separator
Included)
____Variable Speed Air Powered Mixer: Provides Maximum Chemical Efficiency
____110 V Respirator System: 3/4 HP Pump, 100’ Fresh Air Hose and Full Face Mask
____55 Gallon Drum Heater: Thermostatically Controlled/Winter & Cold Environment
____15 CFM Refrigerant Air Dryer: Ensures Clean Dry Air to Gun (Cord & Separator
Included)
____*25 CFM Refrigerant Air Dryer: Same as above
(req. for 7.5 HP Compressor or Larger)
OUTFIT YOUR NEW RIG WITH OUR OTHER POPULAR OPTIONS:
____Additional Build Out Per Foot Cost (customers with larger trailers/trucks)
____*7.5 HP Compressor/High Output Pumps: (req. for high output
roofing/commercial contractors
____5 HP, 22 Amps @ 240 V 60 Gallon “ELECTRIC” Air Compressor (Regulator
Included)
____30kW Industrial Grade “DIESEL” Generator
____50 Ft. Section of Heated Hose with Scuffguard
____Full Recirculation System (Factory Built)
____Gun Cleaning Solvent-5 gallon
____Dynasolve CU6-1 gallon
____Fusion Gun Basic Rebuild Kit
____Additional Fusion Gun with Mix Chamber (specify size)
____Fusion Gun Front End with Mix Chamber (specify size)
